SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 features z 155mbps data links z up to 20km point-point transmission on smf z 1310nm fp transmitter and 1550nm pin receiver for SPL-35-03-EBX-IDFM z 1550nm fp transmitter and 1310nm pin receiver for spl-53-03-ebx-idfm z sfp msa package with lc connector z +3.3v single power supply z operating case temperature:-40~+85c z rohs compliant regulatory compliance table 1 - regulatory compliance feature standard performance electrostatic discharge (esd) to the electrical pins mil-std-883e method 3015.7 class 1 electrostatic discharge (esd) to the duplex lc receptacle iec 61000-4-2 compatible with standards electromagnetic interference (emi) fcc part 15 class b compatible with standards laser eye safety fda 21cfr 1040.10 and 1040.11 en60950, en (iec) 60825-1,2 compatible with class i laser product. rohs 2002/95/ec 4.1&4.2 2005/747/ec compliant with rohs absolute maximum ratings table 2 - absolute maximum ratings parameter symbol min. typical max. unit notes storage temperature t s -40 - +85 c supply voltage v cc -0.5 - +3.6 v operating relative humidity rh +5 - +95 %
SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 recommended operating conditions table 3 ? recommended operating conditions parameter symbol min. typical max. unit notes operating case temperature t c -40 - +85 c power supply voltage v cc 3.13 3.3 3.47 v power supply current i cc - - 300 ma power dissipation p d - 1.041 w data rate 155 mbps optical characteristics table 4 ? optical characteristics: SPL-35-03-EBX-IDFM transmitter parameter symbol min. typical max. unit notes centre wavelength c 1260 1310 1360 nm average output power p 0ut -14 -8 dbm 1 spectral width (rms) ? 2.5 7 nm extinction ratio ex 10 db optical isolation 30 db optical eye mask itu-t g.957 compatible 2 receiver centre wavelength c 1450 1550 1580 nm receiver sensitivity p in -32 dbm 3 receiver overload p in -8 dbm 3 return loss 14 db los assert los a -45 dbm los deassert los d -34 dbm los hysteresis 0.5 5 db notes: 1. the optical power is launched into smf 2. measured with a prbs 2 23 -1 test pattern @155mbps. 3. measured with prbs 2 23 ?1 test pattern@155mbps, ber 110 -10 .
SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 table 5 ? optical characteristics: spl-53-03-ebx-idfm transmitter parameter symbol min. typical max. unit notes centre wavelength c 1450 1550 1580 nm average output power p 0ut -14 -8 dbm 1 spectral width (rms) ? 2.5 4.6 nm extinction ratio ex 10 db optical isolation 30 db optical eye mask itu-t g.957 compatible 2 receiver centre wavelength c 1260 1310 1360 nm receiver sensitivity p in -32 dbm 3 receiver overload p in -8 dbm 3 return loss 14 db los assert los a -45 dbm los deassert los d -34 dbm los hysteresis 0.5 5 db notes: 1. the optical power is launched into smf 2. measured with a prbs 2 23 -1 test pattern @155mbps. 3. measured with prbs 2 23 ?1 test pattern@155mbps, ber 110 -10 . electrical characteristics table 6 ? electrical characteristics transmitter parameter symbol min. typical max. unit notes data input swing differential v in 500 2400 mv 1 input differential impedance z in 90 100 110 ? tx_dis disable v d 2.0 v cc v tx_dis enable v en gnd gnd+0.8 v tx_ fault (fault) 2.0 vcc+0.3 v tx_ fault (normal) 0 0.8 v receiver data output swing differential v out 370 2000 mv 1 rx_los fault v los-fault 2.0 vcc+0.3 v rx_los normal v los-normal gnd gnd+0.8 v notes:
SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 1. internally ac coupled recommended host board power supply circuit figure 1, recommended host board power supply circuit recommended interface circuit figure 2, recommended interface circuit pin definitions figure 3 below shows the pin numbering of sfp electrical in terface. the pin functions are described in table 7 with some accompanying notes .
SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 pin 10 pin 1 pin 11 pin 20 bottom view of board of board top view figure 3, pin view table 7 - pin function definitions pin no. name function plug seq. notes 1 veet transmitter ground 1 2 tx fault transmitter fault indication 3 note 1 3 tx disable transmitter disable 3 note 2 4 mod-def2 module definition 2 3 note 3 5 mod-def1 module definition 1 3 note 3 6 mod-def0 module definition 0 3 note 3 7 rate select not connected 3 8 los loss of signal 3 note 4 9 veer receiver ground 1 10 veer receiver ground 1 11 veer receiver ground 1 12 rd- inv. received data out 3 note 5 13 rd+ received data out 3 note 5 14 veer receiver ground 1 15 vccr receiver power 2 16 vcct transmitter power 2 17 veet transmitter ground 1 18 td+ transmit data in 3 note 6 19 td- inv. transmit data in 3 note 6 20 veet transmitter ground 1 notes : 1. tx fault is an open collector output, which should be pulled up with a 4.7k~10k ? resistor on the host board to a voltage between 2.0v and vcc+0.3v. logic 0 indicates no rmal operation; logic 1 indicates a laser fault of some kind. in the low state, the out put will be pulled to less than 0.8v. 2. tx disable is an input t hat is used to shut down the transmitter optic al output. it is pulled up within the module with a 4.7k~10k ? resistor. its states are: low (0~0.8v): transmitter on
SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 (>0.8v, <2.0v): undefined high (2.0~3.465v): transmitter disabled open: transmitter disabled 3. mod-def 0,1,2 are the module definition pi ns. they should be pulled up with a 4.7k~10k ? resistor on the host board. the pull-up voltage shall be vcct or vccr. mod-def 0 is grounded by the module to indicate that the module is present mod-def 1 is the clock line of two wires serial interface for serial id mod-def 2 is the data line of two wires serial interface for serial id 4. los is an open collector output, which should be pulled up with a 4.7k~10k ? resistor on the host board to a voltage between 2.0v and vcc+0.3v. logic 0 indicates normal operation; logic 1 indicates loss of signal. in the low state, the output will be pulled to less than 0.8v. 5. these are the differential receiver output. they are internally ac-coupled 100 ? differential lines which should be terminated with 100 ? (differential) at the user serdes. 6. these are the differential transmitter inputs. t hey are ac-coupled, differential lines with 100 ? differential termination inside the module. eeprom information the sfp msa defines a 256-byte memory map in eeprom describing the transceiver ?s capabilities, standard interfaces, manufacturer, and other informat ion, which is accessible over a 2 wire serial interface at the 8-bit address 1010000x (a0h). the memory contents refer to table 8. table 8 - eeprom serial id memory contents (a0h) addr. field size (bytes) name of field hex description 0 1 identifier 03 sfp 1 1 ext. identifier 04 mod4 2 1 connector 07 lc 3?10 8 transceiver 00 xx 02 00 00 00 00 00 transmitter code xx:10 for SPL-35-03-EBX-IDFM and 08 for spl-53-03-ebx-idfm 11 1 encoding 03 12 1 br, nominal 02 155mbps 13 1 reserved 00 14 1 length (9um)-km 14 20km 15 1 length (9um) c8 20km 16 1 length (50um) 00 17 1 length (62.5um) 00 18 1 length (copper) 00 19 1 reserved 00 20?35 16 vendor name 53 4f 55 52 43 45 50 48 4f 54 4f 4e 49 43 53 20 ?sourcephotonics?(asc )
SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 36 1 reserved 00 37?39 3 vendor oui 00 1f 22 40?55 16 vendor pn 53 50 4c xx xx 30 33 45 42 58 49 44 46 4d 20 20 35 for SPL-35-03-EBX-IDFM(asc ) 53for spl-53-03-ebx-idfm (asc ) 56?59 4 vendor rev 31 30 20 20 asc ( ?31 30 20 20? means 1.0 revision) 60-61 2 wavelength 05 1e/06 0e 1310nm/1550nm 62 1 reserved 00 63 1 cc base xx check sum of bytes 0 - 62 64?65 2 options 00 1a los, tx_fault and tx_disable 66 1 br, max 00 67 1 br, min 00 68?83 16 vendor sn xx asc . 84?91 8 vendor date code xx year (2 bytes), month (2 bytes), day (2 bytes) 92 1 diagnostic type 58 93 1 enhanced option b0 94 1 sff-8472 02 95 1 cc ext xx check sum of bytes 64 - 94 96-255 160 vendor specific note: the ?xx? byte should be filled in according to practica l case. for more information, please refer to the related document of sff-8472 rev 9.5. table 9-monitoring specification parameter range accuracy calibration * temperature -40 to +95c 3c external voltage 2.97 to 3.63v 3% external bias current 3ma to 80ma 10% external tx power -8 to -1 4dbm 3db external rx power -8 to -32d bm 3db external
SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 mechanical diagram figure 5, mechanical design diagram of the sfp with spring-latch order information table 10 ? order information part no. application data rate laser source fiber type SPL-35-03-EBX-IDFM 100base-bx10-u 155 mbps 1310nm fp tx/1550nm pin rx smf spl-53-03-ebx-idfm 100base-bx10-d 155 mbps 1550nm fp tx/1310nm pin rx smf warnings handling precautions: this device is susceptible to damage as a resu lt of electrostatic disc harge (esd). a static free environment is highly recommended. follow guide lines according to proper esd procedures. laser safety: radiation emitted by laser devic es can be dangerous to human eyes. avoid eye exposure to direct or indirect radiation. legal notice important notice! all information contained in this document is subject to change without notice, at source photonics?s sole and absolute discretion. source photonics warrants performance of its products to current specifications only in accordance with the company?s standard one-year warran ty; however, specifications designated as ?preliminary? are given to describe components only, and source photonics expressly disclaims any and all warranties for said
SPL-35-03-EBX-IDFM spl-53-03-ebx-idfm d s - 6 5 2 3 r e v 0 1 2 0 12-2-1 3 products, including express, implied, and statutory warranties, warranties of merc hantability, fi tness for a particular purpose, and non-infringement of proprietary rights. please refer to the company?s terms and conditions of sale for further warranty information. source photonics assumes no liability fo r applications assistance, customer pr oduct design, software performance, or infringement of patents, services, or intellectual proper ty described herein. no license, either express or implied, is granted under any patent right, copyright, or inte llectual property right, and source photonics makes no representations or warranties that t he product(s) described herein are free fr om patent, copyright, or intellectual property rights. products described in this document are not intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. source p hotonics customers using or selling products for use in such applications do so at their own risk and agree to fu lly defend and indemnify source photonics for any damages resulting from such use or sale. the information contained in this document is provided on an ?as is? basis. customer agrees that source photonics is not liable fo r any actual, consequential, exemplary, or other damages arising directly or indirectly from any use of the informat ion contained in this document. customer must contact source photonics to obtain the latest version of this publication to verify, befor e placing any order, that the information contained herein is current. contact u.s.a. headquarters 20550 nordhoff street chatsworth, ca 91311 usa tel: +1-818-773-9044 fax: +1-818-773-0261 china building #2&5, west export processing zone no. 8 kexin road, hi-tech zone chengdu, 611731, china tel: +86-28-8795-8788 fax: +86-28-8795-8789 taiwan 9f, no 81, shui lee rd. hsinchu, taiwan, r.o.c. tel: +886-3-5169222 fax: +886-3-5169213 ? copyright source photonics, inc. 2007~2012 all rights reserved
|
